Sintered Teflon Bushings

These sintered Teflon bushings are commonly used in precision machinery, to provide very low friction, dry-running performance.

2 products

Loading filters…

Sintered Teflon Bushings

What are sintered Teflon bushings?

Sintered Teflon bushings, also known as PTFE-lined sintered bronze bushes, are dry-running plain bearings designed for very low friction and wear. They combine a metal backing with a layer of sintered bronze, whose pores are filled with a PTFE-rich mixture. This PTFE surface gives the bush its smooth, slippery running face, so it can operate without oil or grease. They are a reliable choice for precision machinery where lubrication is unwanted, impractical, or would quickly become contaminated.

A standard sintered Teflon bushing is made up of:

  • A metal backing, which gives the thin wall its strength and helps carry heat away
  • A layer of sintered bronze, bonded to the backing, with a porous, sponge-like structure
  • A PTFE-rich mixture filling the bronze pores and forming the running surface
  • A plain cylindrical shape, with a sizing joint along its length.

The PTFE transfer film is what makes these bushes run dry.

  • As the shaft starts to move, a small amount of PTFE is transferred onto the shaft, coating it with a thin, slippery film.
  • This film protects the shaft surface and keeps friction low, while the sintered bronze underneath holds more PTFE in reserve as the surface slowly wears.

Sintered Teflon bushings are sized by their bore, outside diameter, and length.

Why are sintered Teflon bushings essential?

Sintered Teflon bushings give smooth, consistent movement with no lubrication and no maintenance. Because there is no oil or grease, there is nothing to dry out, leak, or attract dust and grit, which makes them ideal for sealed, hard-to-reach, and clean applications.

Their very low friction prevents the stick-slip, jerky movement that can occur in plain bearings at start-up, and they cope well with rotating, oscillating, and short sliding movements. The thin wall also saves space, allowing compact housings and lighter designs.

Typical applications include:

  • Shock absorbers and suspension struts
  • Hydraulic cylinders and rams
  • Gear pumps and gear motors
  • Axial and radial piston pumps and motors
  • Precision machinery and instruments
  • Packaging and printing machinery
  • Office equipment and appliances
  • Hinges, pivots, and linkages in hard-to-reach places

The main types of sintered Teflon bushings

  • Plain sintered Teflon bushes - Straight cylindrical bushes, pressed into a housing to support a shaft radially. They are the most common type.
  • Flanged sintered Teflon bushes - Bushes with a flange at one end, which locates the bush in its housing and takes light axial loads.
  • Sintered Teflon thrust washers - Flat washers with the same PTFE running surface, used for axial loads alongside a bush.
  • Metric sizes - Made in a wide range of standard metric bores, outside diameters, and lengths, to suit common shaft and housing sizes.

How to choose the right sintered Teflon bushings?

  • Size - Choose a bush with a bore to suit the shaft, an outside diameter to suit the housing, and a length to suit the space available.
  • Plain or flanged - Choose a flanged bush where the bush needs locating or where there is a light end load.
  • Movement - Sintered Teflon bushes suit rotating, oscillating, and short-stroke sliding movement, especially where smooth, stick-free running matters.
  • Load and speed - They suit light to medium loads. Very high loads combined with high speeds create heat, which wears the PTFE surface faster.
  • Shaft finish - Use a smooth, hardened shaft. A rough or soft shaft will quickly wear through the PTFE surface.
  • Lubrication - These bushes are designed to run dry. Where oil is already present, such as in hydraulic equipment, they can also run in oil.

Essential references and specialised ranges

How the numbering works:

Metric sintered Teflon bushes are usually referenced by a type code, then the bore and the length in millimetres. The outside diameter is fixed for each bore size, so it is not shown in the code. For example:

MB1525 = plain bush, 15mm bore, 25mm long, with a 17mm outside diameter

MB2015 = plain bush, 20mm bore, 15mm long, with a 23mm outside diameter

Suffixes:

D = PTFE-lined dry-running material

F = flanged bush

B = bronze backing, rather than steel

Suffix codes vary between manufacturers, so check the supplier’s catalogue for the exact meaning.

FAQ - All you need to know about sintered Teflon bushings

What is the difference between sintered Teflon and sintered bronze bushes?

Both use sintered bronze, but in different ways. A sintered bronze bush is solid porous bronze filled with oil. A sintered Teflon bush has a thin sintered bronze layer filled with PTFE, so it runs completely dry.

Do sintered Teflon bushings need grease or oil?

No. The PTFE surface is self-lubricating and the bush is designed to run dry. Grease is not needed and can trap dirt, but the bush will happily run in oil where oil is already present.

What is the transfer film?

When the bush first runs, a thin layer of PTFE is passed onto the shaft. This film keeps friction low, protects the shaft, and is the reason these bushes can run without lubrication.

Can I ream or machine a sintered Teflon bush?

No. The PTFE running surface is very thin, and reaming or machining would remove it. The bush reaches its correct bore size when pressed into a correctly sized housing.

How do I fit a sintered Teflon bush?

Press the bush squarely into a clean, correctly sized housing with a press and a fitting mandrel, never by hammering on it directly. Position the joint away from the main load where possible, and check the shaft turns freely afterwards.

How do I identify the bush I need?

Check the code on the old bush or in the machine’s parts list. If it cannot be read, measure the bore, outside diameter, and length with callipers, and on a flanged bush, the flange diameter and thickness.

How can I tell if a sintered Teflon bush needs replacing?

Warning signs include:

  • The grey PTFE surface worn away, showing bronze underneath
  • Squeaking, juddering, or increased friction
  • Play or wobble in the shaft
  • Scoring or marks on the shaft or bore
  • The bush moving or turning in its housing
  • Cracking or opening at the joint